HWWD02A（WRD06）Z-Wave Dimmer Switch Advanced Settings
Here is a full list of advanced settings (parameters) for HWWD02A（WRD06）Z-Wave Dimmer Switch:
Some parameters were added in later firmware updates so please make sure you're on the latest firmware to have all of the settings below available.
LED Indicator Modes
Parameter 1: 0x01 (1)
Choose the LED indicator mode for the Dimmer Switch. The LED indicator to turn on when the Dimmer Switch is on or off, or it to remain on or off at all times, or work in night light mode.
Values: 0 - LED always off; 1 - LED always on; 2 - LED on when dimmer on,LED off when dimmer off; 3 - The LED indicator brightness is 100%, and it changes to 30% after 1 minute, when dimmer off; LED off when dimmer on.
Default: 2
Size: 1 byte dec
LED Indicator Color
Parameter 2: 0x02 (2)
Choose LED indicator color for the Dimmer Switch load status.
Values: 0 – Blue; 1 – Red.
Default: 0
Size: 1 byte dec
LED Indicator Brightness Level
Parameter 3: 0x03 (3)
Choose LED indicator brightness level for the Dimmer Switch load status.
Values: 3–10, where 3 is the lowest brightness level and 10 is the highest brightness level.
Default: 10
Size: 1 byte dec
Restores State After Power Failure
Parameter 4 : 0x04 (4)
Set the on/off status for the relay after power failure.
Values: 0 – Always off; 1–99 – Turn on at the selected brightness level; 100 – Restore the state and brightness level from before the power failure.
Default: 100
Size: 1 byte dec
Scene Button 1 Brightness Level
Parameter 5: 0x05 (5)
Adjust custom brightness level for Scene Button 1
Values: 0–99 – Brightness level in percent.
Default: 25
Size: 1 byte dec
Scene Button 2 Brightness Level
Parameter 6: 0x06 (6)
Adjust custom brightness level for Scene Button 2.
Values: 0–99 – Brightness level in percent.
Default: 50
Size: 1 byte dec
Scene Button 3 Brightness Level
Parameter 7: 0x07 (7)
Adjust custom brightness level for Scene Button 3.
Values: 0–99 – Brightness level in percent.
Default: 75
Size: 1 byte dec
Scene Button 4 Brightness Level
Parameter 8: 0x08 (8)
Adjust custom brightness level for Scene Button 4.
Values: 0–99 – Brightness level in percent.
Default: 99
Size: 1 byte dec
Kick start Brightness Level
Parameter 9: 0x09 (9)
Set the kick start brightness level (in %) for your dimmer. This setting is useful for fixtures that won't turn on when starting from a low brightness level.
Values: 0 – Kick-start disabled; 1–99 – Kick-start brightness level in percent.
Default: 90
Size: 1 byte dec
Dimming Speed
Parameter 10: 0x0A (10)
Set the number of seconds it takes to get from 0% to 100% brightness when pressing and holding the button.
Values: 0 – Instant transition; 1–99 – Transition time in seconds.
Default: 5
Size: 1 byte dec
Minimum Brightness
Parameter 11: 0x0B (11)
Set the minimum brightness level (in %) for your dimmer. You won't be able to dim the light below the set value.
Values: 1–45 – Minimum brightness level in percent.
Default: 1
Size: 1 byte dec
Maximum Brightness
Parameter 12: 0x0C (12)
Set the maximum brightness level (in %) for your dimmer. You won't be able to add brightness to the light beyond the set value.
Values: 55–99 – Maximum brightness level in percent.
Default: 99
Size: 1 byte dec
Auto Turn-Off Timer
Parameter 13: 0x0D (13)
Use this parameter to enable or disable the auto turn-off timer function (the time after which you want the dimmer to automatically turn off once it has been turned on). Auto-off timer will automatically turn the dimmer off after x seconds once it has been turned on.
Values: 0 – Timer disabled; 1–2678400 – Timer duration in seconds.
Default: 0
Size: 4 bytes dec
Auto Turn-On Timer
Parameter 14: 0x0E (14)
Use this parameter to enable or disable the auto turn-on timer function (the time after which you want the dimmer to automatically turn on once it has been turned off). Auto on timer will automatically turn the dimmer on after x seconds once it has been turned off.
Values: 0 – Timer disabled; 1–2678400 – Timer duration in seconds.
Default: 0
Size: 4 bytes dec
Dimming Step
Parameter 15: 0x0F (15)
Set the dimming step size per short press for the Up/Down buttons
Values: 1–10 – Brightness adjustment per tap in percent.
Default: 5
Size: 1 byte dec
Load Control and Scene Control
Parameter 16: 0x10 (16)
Choose Load Control And Scene Control
Values: 0 – Load control and scene control disabled; 1 – Load control enabled and scene control disabled; 2 – Scene control enabled and load control disabled; 3 – Load control and scene control enabled.
Default: 3
Size: 1 byte dec
Status Report Type
Parameter 17: 0x11 (17)
Choose physical and Z-Wave triggers for the Dimmer Switch to send a status change report to the hub.
Values: 0 – Send nothing.; 1 – Send Basic Report.; 2 – Send Switch Multilevel Report; 3 – Send Basic Report and Switch Multilevel Report.
Default: 2
Size: 1 byte dec
433 MHz Remote Controller 1 Address
Parameter 18: 0x12 (18)
Set or delete 1# 433 remote control address for the Dimmer Switch.
Values: 0 – 433MHz remote controller unpaired.; 1–1048575 – remote controller address.
Default: 0
Size: 4 bytes dec
433 MHz Remote Controller 2 Address
Parameter 19: 0x13 (19)
Set or delete 2# 433 remote control address for the Dimmer Switch.
Values: 0 – 433MHz remote controller unpaired.; 1–1048575 – remote controller address.
Default: 0
Size: 4 bytes dec
433 MHz Remote Controller 3 Address
Parameter 20: 0x14 (20)
Set or delete 3# 433 remote control address for the Dimmer Switch.
Values: 0 – 433MHz remote controller unpaired.; 1–1048575 – remote controller address.
Default: 0
Size: 4 bytes dec
433 MHz Remote Controller 4 Address
Parameter 21: 0x15 (21)
Set or delete 4# 433 remote control address for the Dimmer Switch
Values: 0 – 433MHz remote controller unpaired.; 1–1048575 – remote controller address.
Default: 0
Size: 4 bytes dec
433 MHz Remote Controller 5 Address
Parameter 22: 0x16 (22)
Set or delete 5# 433 remote control address for the Dimmer Switch.
Values: 0 – 433MHz remote controller unpaired.; 1–1048575 – remote controller address.
Default: 0
Size: 4 bytes dec
Note:
How to pair 433MHz Magnetic Remote Controller into the Dimmer Switch ?
1. Press and hold the Dimmer Switch ON/OFF button for 3 seconds until the red indicator blinks slowly, then release the button.
2. Press the 433MHz Magnetic Remote Controller ON or OFF buttons once. The Dimmer Switch LED indicator will turn off, paired successful.
How to unpair 433MHz Magnetic Remote Controller from the Dimmer Switch ?
1. Press and hold the Dimmer Switch ON/OFF button for 8 seconds until the red indicator blinks fast, then release the button.
2. Press the Dimmer Switch ON/OFF buttons once. The Dimmer Switch LED indicator will turn off, unpaired successful.